Not sure if you've sorted this yet, but only just noticed it. The confusion comes from arguments over what model was what version. For a while there were arguments over which model number=which version.
Nov 14, 2016. Slimline PS2s. SCPH 39001 iirc, are there any install diagrams for it? Has the diagrams for v5. Slim PS2 7500x Modbo 4.0 Install Valfore, Aug 11, 2015,.
Diagrams, well they seem to be a complete mess at the moment. I'm not sure if it's because it's a clone and they just never bothered with the diagrams or whether they've just become lost over time. You can find the a/b diagrams for the modbo750 here, which as far as I know are the same install points as the modbo 4. The matrix infinity diagrams are also the same, minus the cx point (matrix has an onboard oscillator) for the clock. The only issue may be the cx point. I've seen it in different places on a few diagrams.
So if it doesn't match, you'd have to hunt down a diagram for it. If your board does not match the diagram for the cx point, you should be able to search with the boards number (on the board there is GH-XXX-XX printed on it) and find the correct cx point.
Modchips also exist for the PlayStation 2 and allow for things like playing games from other regions, playing PS1 and PS2 backups, and running homebrew applications. This blog post covers the installation of the Modbo 4.0 modchip into my SCPH-70012 PS2 slim console. Things you’ll need. An SCPH-70012 PS2 slim console. Tools to take apart the PS2 slim. A or modchip. They are pin compatible, I bought my chip from.
30 AWG kynar insulated wire wrapping wire. A soldering iron and solder I initially installed a Modbo 4.0 chip, but ended up swapping it out for a Modbo 5.0 chip. The Modbo 5.0 chip allows booting homebrew directly off of USB flash drives, which is important since the PS2 slim doesn’t have support for an internal hard drive. I’d also like to mention that I was able to install the modchip with a pretty standard 1.6mm chisel tip on my Hakko FX-888D soldering iron. In other words you don’t need a super special tip for your soldering iron. You just need patience, good eyes, and a steady hand. At the time of writing this post I have installed a modchip into two different PS1 systems, two different PS2 systems, and soldered a Teensy to a PS3 slim.
I’ve learned a lot along the way, so I’d like to share some tips that may help your modchip installation experience be a smoother one. Since these tips apply across a lot of posts, I’ve put them into a. Modchip installation diagram Above is an an image of the installation diagram for the Modbo 3.0 diagram for NTSC V12 PS2 slim consoles. This diagram is the same for Modbo 4.0 and Modbo 5.0 chips. If you need a diagram for another version of the PS2 just leave a comment and I’ll upload a copy for you. As you can see from the diagram there are a total of 21 wires that need to be soldered from the PS2 to the modchip.
The chip comes with double sided tape that you use to stick it to the board. I chose to mount my modchip on top of the large chip in the middle of where all of the wires needed to go. I’d recommend finding a lower point on the board instead, since I had to cut away some of the metal shield later on to get the system put back together. You can see an image of the board and where I mounted my modchip above.
Modchip installation With the modchip mounted I soldered each wire to the board. I started with the pads to the right of the chip, and then followed a counter clockwise pattern around the modchip once I finished soldering wires to the pads. Above is an image of what my installation looked like after I finished with the pads. I had the most trouble when it came time to solder wires to the holes, or vias, that are located under the modchip.
Getting solder to stick to the holes was tricky, I’d recommend using some flux to help get the solder flowing. I inserted an image of wires attached so some of the holes above. Eventually I finished soldering all of the wires to the board, and the image above is the result. As you can see I routed four ground wires to the ground pad in the diagram. I’d actually recommend routing the ground to whichever screw hole is closest to the modchip.
It’s also a good idea to use more wires for the 3.3V line as well. Putting everything back together Once I had soldered the modchip to the board, I could put the console back together. I started by taping over all of the points I soldered to, including most of the modchip. Taping prevents any of the connections from being shorted with the case, and also helps hold the wires in place. As I mentioned earlier, I didn’t choose the best position for mounting my modchip. I had to cut away some of the metal shielding to make room for the modchip. Removing the shielding still resulted in a very tight fit when putting everything back together.
Final thoughts I was able to install my modchip my first try in less than an hour. I found the installation process to be more difficult than the installation of a modchip on a PS1, or soldering a Teensy to a PS3 Slim. Laser failure is a problem with V12 PS2 slim consoles, which can be prevented through various methods. From my understanding the best methods are fix, and the. I also read that later date code V12 systems don’t have the issue.
My PS2 slim is a later date code, so I’m going to see if anything bad happens, and just replace the laser if I have to. I’ll update this post if anything happens. This entry was posted in,. Bookmark the.